DodgeTalk Forum

I'm trying to find the ignition fuse location(s). I believe the coils and the injectors share 1 or 2 in the box in the engine bay maybe? I know depend on when the wiring harness was made out can be different colors and I don't especially want to in unravel tape all day to the split to find it. I've got something in the works as per usual. Lol

Anyone know the maximum front payload on a 2001 Ram 3500 van?

My Ignition switch has been Tight to turn the key On and Off and sometimes I had to Hold the Arm up and Jiggle it to move to the On or off position. Now Today, I Turned the key on and I GOT NOTHING! Absolutely Nothing! NOT A SOUND! No Start, No Dashboard Lights , NOTHING at all! This never happened before. ... So, Do I have to get a New Key, Change the Hole Switch or is there another "Rube Goldberg" Solution??? PLEASE HELP. Thanks... DanO'

I have a new to me 2002 ram 1500 that when you turn the cruise on, the cruise light in the cluster comes on and stays on until you turn it off. Problem is, it will not set a speed. I have a ABS code 54 for a shorted dump coil, will that keep it from setting the cruise? That is the only code in the truck except for o2 sensor codes

Hi everyone, it's been a long time since I posted on Challenger Talk. I need to get touch up paint for the 20 X 9.0 Lights Out painted wheels on my 2020 Challenger R/T. I believe the closest match to the Lights Out wheels would be PNW Black Noise, but I'm not 100% sure. The Mopar part number for the PNW touch up paint is 68423870AA. Can anyone help?

Just had Spa day for my'97. Replaced the steering rack and put urethane bushings in. Bought it new and have done all the work since the warranty expired. I have a question about the rear shocks. Can I use the 4wd shocks or do I need to get the 2wd units? My son ordered the 4wd ones and I can't return them.

Helping a friend on limited income with a 2005 Stratus SXT coupe with the 2.4 L Mitsubishi engine. We have tried every drive cycle on the internet to get the EGR and CAT to come ready. There are no trouble or fault codes. A local shop has replaced the EGR valve, checked the O2 sensors, checked for vacuum leaks and driven multiple drive cycles as well. We have driven over 700 miles trying to get the EGR to come ready. I finally located both the Dodge factory manual and the Mitsubishi... Trying to get EGR and CAT to come ready on OBD II reader to pass emission test

I'm from Iowa,my son and I are trying to restore this night runner. Looking for OE black ice rims

Hey so I’ve been battling with my injection pump for a few days now was wondering if we have any experts that have ran into this before. So I was under the assumption that the lever assemblies under the top cover work against each other and were spring loaded. E.g when the one lever is pushed by the fuel screw it will tension the governer spring by pulling the other lever assembly the opposite direction. Problem is mine doesn’t seem to be spring loaded to work against each other. As far as... VE Pump Lever Question

I have a 11 Rt with classic wheels, I like the wheels but there tucked under the wheel wells so much, so I bought 1” wheel spacers. When I went to put them on the studs hit the wheels. I don’t want to cut the studs down is there anything else I can do? Maybe shorter studs. Appreciate any thoughts or pictures of classic wheels spaced out

Hello, I have a 1996 dodge Dakota Sport, it’s been running rough. I can sometimes start the truck up with a normal crank and have it run just fine. But there are times when I’m driving around 45 mph- 50mph and completely come to a stop, at the stop I’ve noticed the truck seems to shake/tremble. When it trembles there are times it will just shut off right there. Then there are times it will take off from the stop light just fine. But then sometimes under acceleration it just shuts off and I... 1996 dodge Dakota: Motor Dying/shut off?

Hi all, new to the forum. I'm a Ford guy, so please excuse my ignorance if there's something someone says that I don't know about. A family member recently picked up a 2009 1500 4x4 with the 5.7 Hemi, previous owner said that the timing chain snapped going down the road. I'm trying to figure out what years of engines aside from '09-'13 will work as a near drop in replacement without too much PCM tomfoolery and need some help. Thanks!