Foro Boating Forum

So this stems from a comment @muc Had made in another thread a few days ago. My 4.3 has a thunderbolt V setup on it with the black denso module. System has been more or less fine aside from that one issue I had where I was getting a backfire through the intake, documented here . Haven't had that issue crop up since last reported in that thread which is good, but curiosity got the better of me this week. My distributor still has the 2 wire pickup, the one without the extra ground... Read more

Mornin' Guys and Gals I just repaced all bellows and lower shift cable on a1996 Alph1 Gen 2. I did all the adjustments as described in the shop manual, and the shifter seems stiff. Both cables move freely when not attached to the bracket, but when connected and adjusted correctly, the movement is stiff. I routed the new cable the same as before by pulling a string through when removing the old cable. Any suggestions to get the shifter to move more freely. Thanks, Ken

I’m trying to plug the tachometer wiring harness into the front of my mercury control box. The plug is D shaped. What is the proper position of the D plug when inserting into the control box. I’m having a hard time getting it to line up and I’m afraid I’ll damage the pins inside the box if I force it. Thank you in advance.

Like my 9 mm, 45, 9 x 18 , 32s, etc. haven’t shot my 44 yet though

Picked up a 92 Bayliner Bayliner for next to nothing to restore. Have already removed the outboard built a stand and threw a battery and throttle on it just in case I need them. Removed some of the interior and as I expected needs a new transom and stringers, as these boats weren't the best built. The fiberglass resin was peeling off the floor like paint. Will also need some gel coat repair. My question is for the fuel tank. I'm assuming it's the original tank from 92. How long are the life... Read more

Carbureted engine, PCM 351 BOSS. So far tried rebuilding original carb, then purchased another factory style carb, then replaced fuel pump and then replaced the factory ignition and finally, got a completely different brand new holley carb. Nothing every changed, Stalls when you give it too much throttle from a stand still. In cruise, accelerates fine when you give it full throttle. You can see the accelerator pump working too. Really going crazy with this one. thinking vacuum leak maybe... Read more

Hello, I recently bought a 1993 Johnson 9.9 2 stroke outboard. It was sitting for close to 20 years but the previous owner ran it out of gas before putting it away in a barn. He claims that it was only ran 3 times and it looks brand new under the cover. When I hooked up a fresh tank of gas it ran flawlessly. After that I had it out around 5 days and it was running perfectly. Last week when I had it out it started running very rough throughout the entire RPM range. I got home and took the... Read more

Ran this engine with no oil in the gas for about 5 minutes. Yes, I know. It started to slow down ... and stopped. Did NOT actually seize, I am going to fog it several times and run it on double oil for 1/2 hour or so. Anyone else has success doing something else/additional? Thanks in advance.

Tengo un Evinrude 175hp ocean pro y quisiera ganar más rpm

Thanks to hurricane Helena in Sept 2024, a large pine fell on my River Hawk boat with my motor on it and broke several parts including the swivel bracket. I am not wanting to remove any thing unnecessarily and would appreciate a little guidance on the correct steps.

MERRILL, WI (MDH) — Hundreds of Lincoln County deer stands may soon require residential building permits after inspectors discovered that local hunters have quietly transformed the traditional plywood box into what officials are calling “unlicensed seasonal condominiums with gun windows.” The investigation began when County Inspector Gary “Load-Bearing Brat” Juedes visited a wooded property outside Merrill expecting to examine a collapsing ladder. Instead, he discovered a two-story hunting... Read more

Hi folks, I'm newbie in the Johnson motors and met the next problem: Working through a full rebuild on this motor — carb rebuilt, fuel pump rebuilt, points gapped at .020, spark good on both cylinders. Motor starts and runs fine at FAST but won't hold a stable idle; throttle plate barely opens at SLOW/START positions. Traced it to the armature plate not reaching its correct SLOW/START position — it reaches full advance fine (hits the mechanical stop at FAST), but on the low end there's... Read more