Back in April I posted the patched Honda ESM as a 274 MB zip. It's now a website: Honda Accord ESM Same official Honda factory workshop manuals for the Mk7 (2003–2008: CL7, CL9, CM1, CM2, CN1, CN2) and Mk8 (2009–2010: CU1, CU2, CU3, CW1, CW2, CW3), Shop Manual and Body Repair for both, but nothing to download or unzip. Open the link on your phone in the garage, pick your year and model code (it's on the V5 next to "Type"), and search. Works in any browser on any... Read more
Forum TypeAccord
typeaccord.co.uk/board ↗Forum XenForo en anglais. 12 rubriques suivies : 7th Gen Accord, 7th Gen DIY, 8th Gen Accord, Announcements, Faults, Forum Feedback, Honda Accord Chat, Member Problems, Modifying, Petrol Faults, TypeAccord General Chat et Welcome.
- Discussions par jour
- 7
- Discussions collectées
- 314
- Messages par jour
- 319
- Rubriques
- 12
- Sources suivies
- 13
- Moteur
- XenForo
Dernières discussions
Relevé toutes les 4 heures depuis le flux public du forum. Seuls le titre, le lien et le début du message sont repris ; chaque lien renvoie à la source.
Back in April I posted the patched Honda ESM as a 274 MB zip. It's now a website: Honda Accord ESM Same official Honda factory workshop manuals for the Mk7 (2003–2008: CL7, CL9, CM1, CM2, CN1, CN2) and Mk8 (2009–2010: CU1, CU2, CU3, CW1, CW2, CW3), Shop Manual and Body Repair for both, but nothing to download or unzip. Open the link on your phone in the garage, pick your year and model code (it's on the V5 next to "Type"), and search. Works in any browser on any... Read more
Do i need to loosen the sub frame to change the front sway bar bushings? 2009 Tourer DTEC.
Do i need to loosen the sub frame to change the front sway bar bushings? 2009 Tourer DTEC.
Having never wanted to not have a real spare wheel a did buy one from a Honda civic from a scrap yard and put it in the back of my 2014 estate. Always having to take it out when going to the tip etc i decided to see if i could get it in the floor pan so to speak. On removing all the carpets and mouldings i now have the spare wheel where it should be. out of sight ready to use if need be. Anyone else done this ?
Does enny one know where i can get a DAB radio 08D02 TLO kit
Does enny one know where i can get a DAB radio 08D02 TLO kit
Honda Accord CL9 (2004, 2.4 Manual): Clutch Pedal Failure — Diagnosis and Replacement Guide Quick summary: If your CL9 develops a creaking clutch pedal, a very low bite point, difficult engagement of first or reverse, or cruise control that suddenly stops working, inspect the clutch pedal bracket before condemning the clutch or hydraulics. In my case, the pedal bracket had cracked and was flexing away from the floor. Car: 2004 Honda Accord CL9, 2.4-litre petrol, manual... Read more
Hi. Having to think hard on replacing the clutch on our Tourer. Just over 102K miles. Quoted £1250 inc VAT fitted at the local garage in Reading. Clutch is not slipping, pedal is just very hard to press and garage reckons its the clutch spring getting to end of life. My worry, beyond the bill being well over 50% of the value of the car, is that the split the transmission and tell me the flywheel needs replacing as well. Anyone have experience with a 2.4 at this mileage they could share... Read more
Hi. Having to think hard on replacing the clutch on our Tourer. Just over 102K miles. Quoted £1250 inc VAT fitted at the local garage in Reading. Clutch is not slipping, pedal is just very hard to press and garage reckons its the clutch spring getting to end of life. My worry, beyond the bill being well over 50% of the value of the car, is that the split the transmission and tell me the flywheel needs replacing as well. Anyone have experience with a 2.4 at this mileage they could share... Read more
Needing help Have a 2009 CL7 UK. I've done a full CL7 Euro R swap, engine/box looms etc. Only issues I'm having is car won't start off the key, believe no power is getting to starter, will start with key in position 2 and feeding starter direct from battery and the abs/handbrake lights are both illuminated. I've tried jumping pins 4 and 9 but light stays solid so can't get any codes. I'm thinking it's earth related but any advice would be greatly appreciated.
Needing help Have a 2009 CL7 UK. I've done a full CL7 Euro R swap, engine/box looms etc. Only issues I'm having is car won't start off the key, believe no power is getting to starter, will start with key in position 2 and feeding starter direct from battery and the abs/handbrake lights are both illuminated. I've tried jumping pins 4 and 9 but light stays solid so can't get any codes. I'm thinking it's earth related but any advice would be greatly appreciated.
314 discussions collectées depuis le 8 septembre 2026. Suivre ce forum par mot-clé →