Forum Rieju and GasGas Classic Riders Club

Hi, I have a problem with the ignition system—sometimes the spark goes out after the engine warms up. I checked the ignition module, and it’s the one causing the problem. Does anyone have an ignition coil module for sale, or know where I can buy one? I found a replacement for a Skidoo, but unfortunately, the motorcycle doesn’t run well with it, so I’m looking for someone who has one for sale like the one I have—a Ducati Energia.

G'day all, (yes, Aussie ) I've got a EC250 2000, not much is known other than it's got a Wiseco piston, Messico pipe and a 38 PWK A/S1 with odd jetting from memory when I opened up the carb a few years ago. Sea level - 2000ft 15-30 degrees C 70% Humidity I'm now getting around to the bike again, so I ordered the following; Pilot; 40,42,45 Main; 172,175,175,180,182 Needle; This is the fun part, right?? I decided I'd get one of each taper to try out 3 taper=Suzuki NEDJ 2 Taper=Yam N3EG... Read more

Questions about correct thermostat for my '03 EC 300, and where to get it and upper rad hoses. Bike came from Florida, and the owner installed those aftermarket upper hoses that are metal and finned for heat dissipation, and there's a good chance he removed the thermostat, if there is/was one. Bike takes forever to warm up, and I'm re-packing the oily silencer now, I don't think the thing ever gets up to proper temp here in CT. But I can't find any US source for the factory upper hoses... Read more

Questions about correct thermostat for my '03 EC 300, and where to get it and upper rad hoses. Bike came from Florida, and the owner installed those aftermarket upper hoses that are metal and finned for heat dissipation, and there's a good chance he removed the thermostat, if there is/was one. Bike takes forever to warm up, and I'm re-packing the oily silencer now, I don't think the thing ever gets up to proper temp here in CT. But I can't find any US source for the factory upper hoses... Read more

Buongiorno a tutti i membri del gruppo. Sono nuovo e scrivo dall'Italia. Ho appena preso una fse 450 del 2004, alla quale il precedente proprietario ha pasticciato l'impianto elettrico. Ho provato a rimetterla in moto, funziona tutto, pompa benzina, iniettore, pickup, Ma non fa' alcuna scintilla la candela. Ho anche provato a sostituire la bobina, ma il problema non si risolve. Chiedo aiuto a voi. Qualcuno ha avuto problemi simili? Cosa devo controllare? Ho trovato un impianto di una 2003... Read more

I've been fighting with my '03 rear brake pedal since I owned it, always rubbed the clutch cover and I could never get the height like I like it. Bushings seem to be good, it just looks like the arm should have a SLIGHT "dogleg" to clear the clutch cover instead of riding against it. Any suggestions for a good aftermarket, or is the stock the best design? I suppose I COULD install spacers of some kind to move it away from the case.

These are model FG GG3210 46mm forks, on my '03 EC300. Pulled the top caps off, removed the springs, removed the bottom compression valve assemblies, flushed everything (compression valves were gunked up solid), and re-filled with 5W fluid to 125mm fluid height. When I screwed the top caps back down, the rebound adjuster was backed all the way out (no rebound damping) and the fork rebounded after I compressed it as I expected...BOING!..it sprang right back. But when I turned the knob all... Read more

Apologies if this has been asked before, but I can't get the search function to work. I've got a 2011 ec200 with a split tank. It's been plastic welded previously, but it's started to leak again. Does anybody know what other year's tanks will fit? I don't mind making a few minor frame mods if that's required. Thanks in advance

https://rieju.com/en/off-road/148/243/mr-300i-hard-offroad-2027?fbclid=IwY2xjawUGhF1wZG9mAWV4dG4DYWVtAjExAHNydGMGYXBwX2lkEDIyMjAzOTE3ODgyMDA4OTIAAR7d0-X6HBvJ_8v3G_U3hUz4z7t7iygxmxk5QxBjkZZUAI4CaN4T9XqV6hD86g_aem_PwaNBllR0to3gFc9ziFljA

https://rieju.com/en/off-road/148/243/mr-300i-hard-offroad-2027?fbclid=IwY2xjawUGhF1wZG9mAWV4dG4DYWVtAjExAHNydGMGYXBwX2lkEDIyMjAzOTE3ODgyMDA4OTIAAR7d0-X6HBvJ_8v3G_U3hUz4z7t7iygxmxk5QxBjkZZUAI4CaN4T9XqV6hD86g_aem_PwaNBllR0to3gFc9ziFljA

I'm starting a new thread about my Ohlins fork difficulties, the original was kind of specific to removing the top caps, read here for the backstory: https://forum.gasgasrider.org/threads/ohlins-46mm-forks-top-cap-removal-question.26679/ My #1 goal is to simply replace the fork seals, but separating the fork is proving impossible. Started with removing the top cap: The manual says to hold a 17mm nut while turning the top cap with a special tool. Ain't NO WAY to access that 17mm nut... Read more

Just about to pull the springs out of my Ohlins forks to see just what I have, but wondering about this special tool the factory manual refers to, I assume to engage the (2) pin holes in the top cap: Can I use a generic adjustable spanner (adjustable pin spacing) to turn the top cap off, or should I opt for something like the factory tool?