Smart Home Automation Forum forum

How do you connect a thermistor to an analog input?

Hello support team, I have A32 pro, I connected to it ethernet cable. The tuya part i set by wifi. It’s working. When the wifi fail, so no more controlling by tuya. I see on the display of A32 pro “tuya offline”. My question is: Can I keep controlling A32 pro With tuya by ethernet, even if wifi broke?

Hello everyone, I have two F16 boards connected with HA that started to have connection issues. The output from the MQTT logs: Code: 2026-09-20 11:00:44: New connection from x.x.x.12:53372 on port 1883. 2026-09-20 11:00:47: New client connected from x.x.x.12:53372 as &tMAC&t (p4, c1, k120, u'kincony12'). 2026-09-20 11:00:47: Client &tMAC&t [x.x.x.12:53372] disconnected: connection closed by client. 2026-09-20 11:00:50: New connection from x.x.x.11:63968 on port 1883. 2026-09-20 11:00:53: New client connected from x.x.x.11:63968 as kincony11_&tMAC&t (p4, c1, k120, u'kincony11'). 2026-09-20 11:00:53: Client kincony11_&tMAC&t [x.x.x.11:63968] disconnected: connection closed by client. kincony11 is configured to use MQTT for Home Assistant while kincony12 is configured to use standard MQTT as I was trying different solutions but the result is the same: disconnect loop. kincony11 is on fw v3.18.0 kincony12 is on fw v3.27.2 Home Assistant details: Installation method Home Assistant OS Core 2026.9.3 Supervisor 2026.09.2 Operating System 18.3 Frontend 20260826.7 MQTT v7.1.1 As fw v3.27.2 has logging view, this is some output: Code: W (1300036) sd: Failed to mount filesystem. Error: ESP_ERR_INVALID_RESPONSE E (1301096) mqtt_client: esp_mqtt_connect: mqtt_message_receive() returned 0 E (1301096) mqtt_client: MQTT connect failed I (1301096) mqtt: MQTT_EVENT_DISCONNECTED I (1305036) gpio: GPIO[9]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 E (1305236) sdmmc_sd:

Hello everyone, I have two F16 boards connected with HA that started to have connection issues. The output from the MQTT logs: Code: 2026-09-20 11:00:44: New connection from x.x.x.12:53372 on port 1883. 2026-09-20 11:00:47: New client connected from x.x.x.12:53372 as (p4, c1, k120, u'kincony12'). 2026-09-20 11:00:47: Client [x.x.x.12:53372] disconnected: connection closed by client. 2026-09-20 11:00:50: New connection from x.x.x.11:63968 on port 1883. 2026-09-20 11:00:53: New client connected from x.x.x.11:63968 as kincony11_ (p4, c1, k120, u'kincony11'). 2026-09-20 11:00:53: Client kincony11_ [x.x.x.11:63968] disconnected: connection closed by client. kincony11 is configured to use MQTT for Home Assistant while kincony12 is configured to use standard MQTT as I was trying different solutions but the result is the same: disconnect loop. kincony11 is on fw v3.18.0 kincony12 is on fw v3.27.2 Home Assistant details: Installation method Home Assistant OS Core 2026.9.3 Supervisor 2026.09.2 Operating System 18.3 Frontend 20260826.7 MQTT v7.1.1 As fw v3.27.2 has logging view, this is some output: Code: W (1300036) sd: Failed to mount filesystem. Error: ESP_ERR_INVALID_RESPONSE E (1301096) mqtt_client: esp_mqtt_connect: mqtt_message_receive() returned 0 E (1301096) mqtt_client: MQTT connect failed I (1301096) mqtt: MQTT_EVENT_DISCONNECTED I (1305036) gpio: GPIO[9]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 E (1305236) sdmmc_sd: sdmmc_init_sd_if_cond: send_i

here is KinCony AIO Hybrid smart controller work with oxygen modbus sensor using RS485 oxygen-sensor-1.jpg (Size: 401.14 KB / Downloads: 7) oxygen-sensor-2.jpg (Size: 188.69 KB / Downloads: 8) here is oxygen sensor modbus protocol: oxygen-modbus-sensor.png (Size: 162.95 KB / Downloads: 8) here is config sensor in KCS "sensor" webpage, chose "modbus" type of sensor. kcs-oxygen-modbus-sensor.png (Size: 86.49 KB / Downloads: 7) slave: 22 function code: 03 register: 104 data type: uint16 byte order: abcd big endian multiplier: 0.1 KCS monitor will show the sensor value: oxygen-sensor-value.png (Size: 43.16 KB / Downloads: 7)

here is KinCony AIO Hybrid smart controller work with oxygen modbus sensor using RS485 oxygen-sensor-1.jpg (Size: 401.14 KB / Downloads: 25) oxygen-sensor-2.jpg (Size: 188.69 KB / Downloads: 26) here is oxygen sensor modbus protocol: oxygen-modbus-sensor.png (Size: 162.95 KB / Downloads: 31) here is config sensor in KCS "sensor" webpage, chose "modbus" type of sensor. kcs-oxygen-modbus-sensor.png (Size: 86.49 KB / Downloads: 26) slave: 22 function code: 03 register: 104 data type: uint16 byte order: abcd big endian multiplier: 0.1 KCS monitor will show the sensor value: oxygen-sensor-value.png (Size: 43.16 KB / Downloads: 26)

Hello! i have a Kincony A8 i finally try to get working.... the relais i got working, but the inputs don't.... i flashed from esphome the follwoing: esphome: name: kc868-a8 friendly_name: relais_wohnung esp32: variant: esp32 board: esp32dev framework: type: arduino # I2C Bus für die Relais-Ansteuerung i2c: sda: GPIO4 scl: GPIO5 scan: true id: bus_a pcf8574: - id: pcf8574_hub_in_1 address: 0x22 pcf8575: false binary_sensor: - platform: gpio name: "A8 Input 1" pin: pcf8574: pcf8574_hub_in_1 number: 0 mode: INPUT inverted: true - platform: gpio name: "A8 Input 2" pin: pcf8574: pcf8574_hub_in_1 number: 1 mode: INPUT inverted: true - platform: gpio name: "A8 Input 3" pin: pcf8574: pcf8574_hub_in_1 number: 2 mode: INPUT inverted: true - platform: gpio name: "A8 Input 4" pin: pcf8574: pcf8574_hub_in_1 number: 3 mode: INPUT inverted: true - platform: gpio name: "A8 Input 5" pin: pcf8574: pcf8574_hub_in_1 number: 4 mode: INPUT inverted: true - platform: gpio name: "A8 Input 6" pin: pcf8574: pcf8574_hub_in_1 number: 5 mode: INPUT inverted: true - platform: gpio name: "A8 Input 7" pin: pcf8574: pcf8574_hub_in_1 number: 6 mode: INPUT inverted: true - platform: gpio name: "A8 Input 8" pin: pcf8574: pcf8574_hub_in_1 number: 7 mode: INPUT inverted: true logger: api: encryption: key: "*****" ota: - platform: esphome ethernet: type: LAN8720 mdc_pin: GPIO23 mdio_pin: GPIO18 clk: mode: CLK_OUT pin: 17 phy_addr: 0 i tried to put common the pin 3, on GND, then 12V, then GND again.... i tried dire

I just recieved my module and want it to remember the relay state during power loss, how do I do that? Thanks!

Hello! i have a Kincony A8 i finally try to get working.... the relais i got working, but the inputs don't.... i flashed from esphome the follwoing: esphome: name: kc868-a8 friendly_name: relais_wohnung esp32: variant: esp32 board: esp32dev framework: type: arduino # I2C Bus für die Relais-Ansteuerung i2c: sda: GPIO4 scl: GPIO5 scan: true id: bus_a pcf8574: - id: pcf8574_hub_in_1 address: 0x22 pcf8575: false binary_sensor: - platform: gpio name: "A8 Input 1" pin: pcf8574: pcf8574_hub_in_1 number: 0 mode: INPUT inverted: true - platform: gpio name: "A8 Input 2" pin: pcf8574: pcf8574_hub_in_1 number: 1 mode: INPUT inverted: true - platform: gpio name: "A8 Input 3" pin: pcf8574: pcf8574_hub_in_1 number: 2 mode: INPUT inverted: true - platform: gpio name: "A8 Input 4" pin: pcf8574: pcf8574_hub_in_1 number: 3 mode: INPUT inverted: true - platform: gpio name: "A8 Input 5" pin: pcf8574: pcf8574_hub_in_1 number: 4 mode: INPUT inverted: true - platform: gpio name: "A8 Input 6" pin: pcf8574: pcf8574_hub_in_1 number: 5 mode: INPUT inverted: true - platform: gpio name: "A8 Input 7" pin: pcf8574: pcf8574_hub_in_1 number: 6 mode: INPUT inverted: true - platform: gpio name: "A8 Input 8" pin: pcf8574: pcf8574_hub_in_1 number: 7 mode: INPUT inverted: true logger: api: encryption: key: "*****" ota: - platform: esphome ethernet: type: LAN8720 mdc_pin: GPIO23 mdio_pin: GPIO18 clk: mode: CLK_OUT pin: 17 phy_addr: 0 i tried to put common the pin 3, on GND, then 12V, then GND again.... i tried dire

Hello! i have a Kincony A8 i finally try to get working.... the relais i got working, but the inputs don't.... i flashed from esphome the follwoing: esphome: name: kc868-a8 friendly_name: relais_wohnung esp32: variant: esp32 board: esp32dev framework: type: arduino # I2C Bus für die Relais-Ansteuerung i2c: sda: GPIO4 scl: GPIO5 scan: true id: bus_a pcf8574: - id: pcf8574_hub_in_1 address: 0x22 pcf8575: false binary_sensor: - platform: gpio name: "A8 Input 1" pin: pcf8574: pcf8574_hub_in_1 number: 0 mode: INPUT inverted: true - platform: gpio name: "A8 Input 2" pin: pcf8574: pcf8574_hub_in_1 number: 1 mode: INPUT inverted: true - platform: gpio name: "A8 Input 3" pin: pcf8574: pcf8574_hub_in_1 number: 2 mode: INPUT inverted: true - platform: gpio name: "A8 Input 4" pin: pcf8574: pcf8574_hub_in_1 number: 3 mode: INPUT inverted: true - platform: gpio name: "A8 Input 5" pin: pcf8574: pcf8574_hub_in_1 number: 4 mode: INPUT inverted: true - platform: gpio name: "A8 Input 6" pin: pcf8574: pcf8574_hub_in_1 number: 5 mode: INPUT inverted: true - platform: gpio name: "A8 Input 7" pin: pcf8574: pcf8574_hub_in_1 number: 6 mode: INPUT inverted: true - platform: gpio name: "A8 Input 8" pin: pcf8574: pcf8574_hub_in_1 number: 7 mode: INPUT inverted: true logger: api: encryption: key: "*****" ota: - platform: esphome ethernet: type: LAN8720 mdc_pin: GPIO23 mdio_pin: GPIO18 clk: mode: CLK_OUT pin: 17 phy_addr: 0 i tried to put common the pin 3, on GND, then 12V, then GND again.... i tried dire

I just recieved my module and want it to remember the relay state during power loss, how do I do that? Thanks!

Hello, is there included any onboard overvoltage protections to switch inductive load? I need to switch electromagnetic valve 24V / 1A. Thanks Radovan