Plumbing Zone forum

Have a job where home insurance is asking that client remove all PB from their house. Their service line is PB, 1" comes up through the slab. Looking for opinions on best fitting to transition to copper or pex just outside foundations. Options so far are PB/Pex sharkbite wrapped in silicone tape, or an old grey Quest fitting. Wondering about any other compression fittings that may be suitable. Crimps are not to code underground in BC. Also whether stiffeners for PB are available...diff... Underground transition from polybutylene

Are they the same ? Is Sloan better ? What’s your experience ?

I’m looking to relocate to Canada as a master plumber with 15 years of experience. I’ve been licensed in the state of Florida since 2020. I ran a service based company but also has done new construction and plumbing remodel, residential and commercial. I am very experienced in bathroom remodeling and light electric work as well. If you are hiring and know anyone that’s looking for an experienced plumber, hard working, knowledgeable, and punctual, I’m open for work. I will be a great asset to... U.S. master plumber looking to relocate to Canada

I have never seen these valves and of course the supply house rep try to convince me only after carrying them for a few months they were the best !

Hello everyone. I’m looking into upgrading the battery setup for my trolling motor and keep seeing lithium batteries recommended. I currently use lead-acid batteries, but the weight and limited runtime have me considering switching to a lithium trolling motor battery. If you've made the switch, how much did you notice in runtime, weight, charging time, and overall performance? Are lithium batteries reliable enough for frequent fishing trips, and do they actually last long enough to... Is a Lithium Trolling Motor Battery Worth It for Regular Fishing?

After 40 years in the field and the last 18 running my own shop with my wife ,my body has said to stop crawling and digging! We merged with a larger heating and air shop and they want to try and expand the operation while keeping our brand. It is Tapp Plumbing out of Logan Georgia. I will assume more of a management type role now. I was hoping to make it to 70 years of age but the doctor assured me it is no longer healthy for my spine . I am 59, I already miss being out there !

I saw this on face book and I wonder if would actually work https://housewor.com/products/high-pressure-sewer-jetter-hose?utm_medium=paid&utm_id=120242592248160625&utm_content=120242593579180625&utm_term=120242592248140625&utm_campaign=120242592248160625

One coat of tinted primer has been applied. I blocked all the joints and installed two studs in the middle, the pictures don’t show that. Used up some liquid nails I had opened to stick the drywall to the blocking and of course screws. Used a razor knife to bevel the drywall around the perimeter. I’m going to skim the entire wall, lightly sand with 180 grit then prime and apply two coats of paint. Light sanding in between coats. [ATTACH... Drywall Repair

Hello All, I’m having a hell of a time with a Moen bidet faucet replacement on an older Kohler 4 hole. I snugged up the middle nut but the water seems to pool out of the chrome escutcheon when the valve is turned not the port on the procelein. I feel like I maybe need to look into a new as I’m not sure the compatibility. Any thoughts? thanks in advanced Vard View attachment 143664 View attachment 143662 View attachment 143666

Hello All, I’m having a hell of a time with a Moen bidet faucet replacement on an older Kohler 4 hole. I snugged up the middle nut but the water seems to pool out of the chrome escutcheon when the valve is turned not the port on the procelein. I feel like I maybe need to look into a new as I’m not sure the compatibility. Any thoughts? thanks in advanced Vard View attachment 143664 View attachment 143662 View attachment 143666

It’s connected to a water heater and has a double pole 30 amp breaker. Customer sent the pic, I haven’t been to the location yet…..

Hi everyone, I’m looking for some advice on common industrial gearbox problems. We recently started experiencing unusual noise, increased vibration, and occasional overheating from one of our gearboxes during normal operation. The gearbox is properly lubricated, but the issue seems to be getting worse over time. I’d like to understand what could be causing these symptoms and whether they might indicate worn gears, bearing failure, misalignment, or another mechanical problem. What... Common Industrial Gearbox Problems and How to Prevent Them