Fórum DIY Valve Check and Adjustment

The FIZZER CCT KIT is an economical, and immediate solution to the faulty Yamaha CCT. The kit consists of the following: (1) Stainless Steel Set Screw M6 x 1.00 x 25 (1) Stainless Steel Flange Nut M6 x 1.00 (1) High Temperature (500F) Non Metallic Washer (1) Set of Instructions Cost is currently $10 shipped in the US. CANADIAN ORDERS will incur a surcharge and will be sold at $13 SHIPPED . PLEASE SEND PAYMENT AS A GIFT Beginning 4/25/14 we are offering same day... Interest in a CCT set screw kit.

Note: Photo of FJR1300 is to show mounting location of lights previously! I no longer own this bike. I love this new-to-me bike, I downsized fom a '16 FJR1300ES. I don't have engine guards, and I want to mount these lights down low. I ordered a couple of fork tube steering damper clamps (photos) that I'll need to add steel bar to for the mount, but I'm interested in seeing other ideas. I'm aware of the Denali fork tube mounts, but they are no different from what I ordered & plan, other... I just bought a used '19 Tracer 900 Gt. Looking to mount large Denali lights

Just figured i drop a line to to let people know I'm back lurking around the forum. I took an unusually long hiatus due to some life complications. I haven't even had the bike out at all this year. I've missed the comradery.

Hello everyone, I’m starting to loose all hopes and bring my bike to a mechanic but before doing so I might as well try this forum, I will try to keep things as short as possible. I own a 2017 MT-09 with 27k km. Symptom: Long cranking to start when the bike has been sitting (several attempts, engine eventually catches). Once it fires, it runs flawlessly — idle is perfect and stable, pulls cleanly to 10k rpm at full throttle with no hesitation or flat spots. Restarting while hot is instant... Gen 2: Bike cranks fine but is extremely hard to start

Hi all. Does anybody have any experience with using front paddock stands on the newer XSR900's? I bought the Oxford Zero-G Paddock stand Dollys (both front and back) in the hope it would make it easier to position the bike in a small garage. The back dolly works fine, great. But the front does not seem to fit out of the box, as the forks on the front paddock stand can't seem to find a good place to sit. I've tried all kinds of ways and angles, but no luck. The front fork seems to have... Front fork vs Paddock stand : 1-0

Putting the 2024–2026 numbers in one place. Pre-ride Front tire (cold): 36 psi Rear tire (cold): 42 psi Chain slack: 36–41 mm Clutch free play: 5–10 mm Oil: between min/max Brake fluid: above MIN Oil / coolant Oil + filter: 3.2 L Oil, filter left in: 2.8 L Dry fill: 3.5 L Coolant (radiator + lines): 1.72 L Chain / sprockets Size: 525 Links: 110 Slack: 36–41 mm 15-link limit: 239.3 mm... MT-09 2024-2026 specs,fluids,capacities,service intervals

This past weekend I swapped the brake pedal from silver to black using an OEM pedal. Yamaha Part# BEA-27211-10-00 Ordered from PartZilla Took about 10 mins to swap

I'm somewhat at my wits end, and am ready to open up to some help, lol. 2014 Yamaha FZ-09. I'm the third owner. I do not know much about how it was maintained by the first owner, who used it as his daily rider for 26,000 miles, but I'm positive they skipped some oil changes since I had to replace the camshafts. This is my fourth motorcycle. I've put about 1000 miles on the bike, and 100 miles ago, I made a mistake while vacation riding on the Tail in TN by forgetting to check the cap on... Overheating

I bought some Oxford grips that i want to install on '24 MT-09 and control from the dash. chatgpt convinced me (lol) to get the EVO because of the temp regulation. I haven't received them but i just realized that since i'm cutting off the controller, that's not even going to work, right? so, i could've just got the regular ones. or did i get lucky and that feature will work anyway? I got the harness converters and just to confirm about this diagram... Gen 4 heated grips

Hello! I posted here a while ago, when this first happened, and we couldn't really find a solution. Hopefully this helps someone although its not great news. hah... Here is my original post if you need or want additional context... So... After going back and forth with my Yamaha dealer, we eventually had to get on a three-way call with Yamaha USA. Yamaha USA escalated it to... Destroyed ECU? Here’s What Yamaha Japan Told Me

Hello everyone, I’m going to try and keep this straightforward. I have a new 2025 mt09sp (us) my original ecu was lost in the mail during flashing process. I bought a replacement ecu with the same part number and everything. New ecu was flashed plugged in new ecu, key is recognized, and column will unlock and it will power on to the dashboard no problem. However fuel pump does not prime, bike will turn over but will not start. is this a flash problem, or a key fob problem? dealer... MT09sp 2025 ecu swap.