Forum Problemi settaggio governor brain 2 motore non parte ed emette…

I have read and watched many videos and no one seemed to be able to give a simple explanation very simply sab Genesis sport 700 hobbywing 260platinum v5 setup with telemetry all works trying to dial in capacity and trying at various setups , normal, id1 and 2 simply with examples if battery is 5000mah put into setup wizard and you are using 4000 when charging back up what would you put for a correction tried a few with little difference and sometimes when increasing for 10 to 20 in configuration it actually got worse if I understood what this number was doing it may help. is it a percentage? can we go both positive and negative? thank you

He Integration is well working on my FrSky ETHOS XE-S transmitte. But when I click on script, only half of the main radio screen is occupied (on the left part). The text is difficult to read and lines spacers are small. How I do to adjust scrip and the size of main screen of my radio (4.3-inch color.) tanks

I have two Align T-Rex helis which are configured identically, a 600 and a 700 with nitros. After a recent crash, I have rebuilt the 600. It shows the RPMs with Spektrum Back Plate sensor on the Governor Panel in the Brain setup software, but does not display the RPMs on the iX14 Telemetry Display. The 700 works perfectly. I seam to be having trouble binding the SRLX on the 600. I Bind the DSMX satellites ok, but trying to bind the SRLX gives a "Bind Failed" display message but it flashes, and lights up in operation. So I know the Brain is getting the data from the backplate, but the iX14 is not getting the data. Software in Brain is up to date ending in 308.

As usual new Firmware notifications will be automatic, and system will prompt users of the presence of new updates once powered unit is connected to a Windows PC or Android devices or iOS devices with Internet connection active. For those with Brain2/iKon2 that do not frequently use the APP/Software (because the flight controller unit is fine as it was set up), let’s take a look at what is coming with this update (for free) in addition to previous versions already released: – Software: 3.4.308, Firmware: 3.4.308 (73° official release), 08 July 2026: Added reference to zero / center values on panel 5 “Transmitter Setup” of the Wizard and in the same panel in ADVANCED, section 2 “Receiver” Now in the ADVANCED, section 4 “Servos” it is also possible to adjust the Throttle Refresh Frequency Added for “Tail Motor Driven” one initial soft start to avoid tail abrupt movements at tail motor start When in panel 7 “Tail Motor Driven” icon is selected, going to successive panel 8 & 9, tail motor won’t start anymore In the rare instances where the “Support Request” feature does not work, a diagnostic log named “Support_Error_Log.txt” is generated and saved in the user’s Documents folder, which will help us determine the cause of the issue encountered by some users When the multi-protocol icon in Panel 3 of the Wizard is selected, the correct channels for the received protocol type are automatically assigned even if the power of the flight controller is turned off and on before turning on

I recently acquired a Crius BT adapter and connected it to my Brain 2 using an MSH cable, based on your advice here: Brain Software on Android Tablet for non-BlueTooth Brain 2 • General Discussions • MSH-Electronics Forum Before pairing to any of my Android devices, I used my PC and USB cable to rename the Brain 2 and revise the PIN. I then disconnected the PC and paired the Crius to my Android device, and opened the Brain Configuration App on my device. But the Crius adapter is still called CRIUS, and the PIN is the default 0000. Is it possible to rename the Crius adapter and revise the PIN using Brain software? If not, can you point me to resources that allow me to do this? I'm slightly concerned when I go to a fun fly and accidentally connect to someone else's Crius adapter or vice versa. I have another older heli with a Brain 2 BT, where I was able to rename it and revise the PIN. I understand the internal BT device inside that unit is different than the external Crius in the other unit.

Today, I connected my recently acquired Brain 2 with the Crius BT module, and confirmed that I can use the Brain Configuration App on both my phone and my tablet. But on the tablet, when I clicked on Recorded Logs, a new window popped up, entitled Brain Diagnostic(only Brain2/iKon2). See picture. In the picture, you can see the Brain Configuration App in the background. It seems to be prompting me to purchase an additional Brain Diagnostic app for Android. I was unaware of this Diagnostic app, and I can't find any information on it online nor in the Google Play Store. I can only find information for the configuration, which I was already using when this window popped up. I thought I could view recorded logs on the configuration app over bluetooth, like I can on my PC over USB cable. Can you tell me more?

While attempting to set up the Helicopter on the Bench, I am getting random 1609 cut-outs of the Motor, and random, but extreme jittering of all the Servos. The Helicopter is as follows: SAB Kraken S 700 Graupner MZ-32 Tx and GR-16 Rx KDE 700XF 535 Motor Hobbywing 200A Opto V4.1 brand new, I literally just opened it. I bought it 10 years ago for another project. Graupner HCM860 BB MG x3 - Cyclic Graupner HCM880 BB MG x1 - Tail Rx Battery is Turnigy 2S 2600 MAH direct to Ikon2 HD Flight Batteries are 2x Turnigy 6S 5500 MAH The Ikon2 HD is mounted on the elevated FBL Platform (using the 4 provided Rubber Soft Mounts), and the SAB Manual recommended 2mm of Mounting Tape. I used the two Squares of the MSH provided Tape. ESC Telemetry is showing in Transmitter, via Rx Telemetry output. Hobbywing SCM Module used between ESC and Ikon2. "P" Side Voltage and Ground on the output of the SCM is supplied by the GOV Port + and - Pins. The Output "P" Wire from the SCM is in Pin 5 of the 4-5-6 Port. Output from Data Port of ESC to SCM provides ESC Voltage and "P" Signal to ESC Input side of SCM. The GOV Wire, (Orange) from the HW ESC Throttle Wire (4 wire bundle) is in Ikon2 GOV Port, other three Wires (Connector) are in CH-1 for Throttle Control. The Motor is responding to Governor Settings, which were set at 1800, 1900, and 2000. Motor Temp on the Bench is 138 Deg. ESC Temp is 86 Deg. ESC is in Airplane Mode, Voltage Cutoff and Active Freewheel are Disabled. Startup Power is set to 1. Oth

I purchased this cable per suggestion from this post:https://www.msh-electronics.com/forum/general-discussions/brain-software-on-android-tablet-for-non-bluetooth-brain-2/#post-3781 I also ordered a Crius BlueTooth module, which has not yet arrived. I did notice that the cable does not have the same wire color order at both ends, and the connectors are slightly different shapes. It's clear to me which end is to be plugged into the Brain 2 sysport, and which is plugged into the Crius. My question: since the color order is different, is the end that plugs into the Crius in the correct color order? That end is: black, green, red, yellow.

I recently acquired an Android tablet, and simultaneously added another helicopter to my fleet. My older heli has a Brain 2 BT, but my new one has just Brain 2(without BT, because it wasn't available). When I downloaded Brain software to my tablet from the Google Play store today, it installs v3.4.220. I'm aware that the current version is v3.4.275 I connected my new Brain 2 via USB cable to the tablet, and launched Brain software. Instead of recognizing the Brain 2, it keeps asking me to identify which BT device to use. Again, this brand new Brain 2 does not have BT, so I appear to be stuck, because in order to advance, it will only launch in Demo mode. I have been assuming that the Brain software on tablet can utilize the USB connection. Am I wrong about this?

Hi, I'm facing two issues with my Brain2 on a new build. I fly scale/sport style only (no 3D). The heli has about 15-20 flights so far and these issues have been present since the beginning. All Brain2 parameters are at default except where noted below. Setup: XLPower Specter 700 V2 – WC Edition Main Blades: SAB S701 Tail Blades: SAB S105 Motor: XNova Lightning 4525/YY-530KV 10P ESC: Hobbywing Platinum Pro 180A HV V5 Servos: Theta Razor – 3× C1 (cyclic) / 1× T1 (tail) RX: RadioMaster RP3-H TX: RadioMaster TX16S Head speed: 1950 RPM (ESC internal governor) Brain2 firmware: 3.4.275 Mechanical checks I've done: Swashplate is level — pitch measured at multiple rotor positions using the Brain2 Swashplate Setup page (with the software commanding the servos to the zero-pitch position) reads 0° ±0.15°. No tracking issues visible in hover — blades are running in the same plane. Heli is balanced (nose and tail weigh the same). Transmitter is confirmed sending center pulse with stick at neutral. Issue 1 — Constant backward drift in hover: The heli has a persistent tendency to pitch nose-up during hover. It's a small but noticeable drift — after 3–4 seconds of hands-off hover, the heli starts moving backward. This happens regardless of wind direction. I don't experience this behavior on other helis flown at the same location under the same conditions. Issue 2 — Oscillations in forward flight (main concern): I'm seeing two distinct oscillation behaviors during forward flight: (a) Slow pit

Hi, I have a brain 2 HD on a goblin 580 raw ESC is Castle Creations 120HV, using 6s config on the heli I am also using Radiomaster 16S Mkii, and have a native 4 in 1 module. I bound the unit with 2 Spektrum DSMX satellites I updated the Brain2 ( and my PC app) to latest Software release for unit an app on first boot today I have verified that the Brain2 bound correctly, as 3 cyclic and rudder servos are functioning as expected when unit is powered up I have verified that my ESC throttle input cable is correctly plugged into channel 1 on the Brain, and not inverted, wrong pins, etc. I have verified that I am not on throttle hold I have verified that the channel monitor is outputting signal from radio perspective. After the Brain 2 finishes initializing. the swash is responsive, but the ESC LED blinks continuously, indicating either non valid zero signal for off, or is getting no signal at all In an attempt to verify anything is coning out of the brain2 on throttle, I hooked up a servo to channel 1 and it did not move - indicating to me that perhaps no signal is present on this channel - I also verified that servo worked (also tried disconnecting one of the functioning Cyclic servos and moved it into Channel 1) - both test failed to move servo I have tried numerous throttle curves including 2 point linear (-100 to 100) - 0 to 100, ramp to 60% etc - nothing works I have tried setting ESC into calibration mode by powering up heli with throttle stick full forward and also, nothing

As usual new Firmware notifications will be automatic, and system will prompt users of the presence of new updates once powered unit is connected to a Windows PC or Android devices or iOS devices with Internet connection active. For those with Brain2/iKon2 that do not frequently use the APP/Software (because the flight controller unit is fine as it was set up), let’s take a look at what is coming with this update (for free) in addition to previous versions already released: – Software: 3.4.275, Firmware: 3.4.275 (72° official release), 18 February 2026: NOTE: for users utilizing the Crossfire protocol: it is necessary to perform an automatic “Discover New” of the telemetry parameters to activate the new parameters and then manually delete the obsolete ones that are no longer transmitted. For updated information, refer to section 12 on page 14, ‘Crossfire’ in the new version of PDF manual “Telemetry.” Increased the precision and the refresh rate of External Variometers (Barometers) Added decoding of the “Atmospheric Pressure hPa” parameters of the External Variometric sensors, now included in the recordable parameters Added decoding of the “Air Temperature °C” parameters of the External Variometric sensors, now included in the recordable parameters Added a decimal place to the vertical scales of the variometer parameter graphs (AbsAltitude, RelAltitude, Vspeed) relating to decimeters per second in the Realtime & Recorded Logs sections Implemented decoding of Kiss telemetry fro